Commissioners Information Bulletins Customer Enquiry Centre Trade Skills Recognition Home Search Contacts
  DET Apprenticeships and TraineeshipsAbout Us
  Use of the search engine is highly recommended. To use, click on the search button above.
 
Automotive
Building and Construction
Communications
Food
Forestry
Furnishing, Light Manufacturing, Textile Clothing and Footwear
Manufacturing Engineering
Primary Industries
Process Manufacturing
Retail and Wholesale
Utilities and ElectroTechnology
 
 


MEM30405 Certificate III in Engineering - Electrical/Electronic

Applicants for trade recognition should provide evidence to demonstrate at least 4 years practical experience in the following trade competencies.

In addition to any other evidence supporting an application for trade recognition, applicants are encouraged to use this checklist as a self assessment competency guide and lodge it with the application.

Units of Competency Check
MEM12.23A Perform engineering measurements
MEM12.24A Perform computations
MEM13.14A Apply principles of occupational health and safety in the work environment
MEM14.4A Plan to undertake a routine task
MEM14.5A Plan a complete activity
MEM15.2A Apply quality systems
MEM15.24A Apply quality procedures
MEM16.6A Organise and communicate information
MEM16.7A Work with others in a manufacturing, engineering or related environment
MEM16.8A Interact with computing technology
MEM17.3A Assist in the provision of on the job training
Electrical/Electronic Trade stream units Check
MEM5.1B Perform manual soldering/desoldering - electrical/electronic components
MEM5.2B Perform high reliability soldering and desoldering
MEM5.3B Perform soft soldering
MEM5.6B Perform brazing and/or silver soldering
MEM9.2B Interpret technical drawing
MEM10.2B Terminate and connect electrical wiring
MEM10.3B Install and test electrical wiring and circuits up to 1000 volts a.c. and 1500 volts d.c.
MEM12.2B Perform electrical/electronic measurement
MEM12.4B Perform precision electrical/electronic measurement
MEM18.1C Use hand tools
MEM18.2B Use power tools/hand held operations
MEM18.45B Fault find/repair electrical equipment/components up to 250 volts single phase supply
MEM18.46B Fault find/repair electrical equipment/components up to 1000 volts a.c./1500 volts d.c.
MEM18.47B Diagnose and maintain electronic controlling systems on mobile plant
MEM18.48B Fault find and repair/rectify basic electrical circuits
MEM18.49B Disconnect/reconnect fixed wired equipment up to 1000 volts a.c./1500 volts d.c.
MEM18.50B Disconnect/reconnect fixed wired equipment over 1000 volts a.c./1500 volts
d.c.
MEM18.51B Fault find and repair/rectify complex electrical circuits
MEM18.52B Maintain fluid power systems for mobile plant
MEM18.54B Fault find, test and calibrate instrumentation systems and equipment
MEM18.55B Dismantle, replace and assemble engineering components
MEM18.56B Diagnose and repair analog equipment and components
MEM18.57B Maintain/service analog/digital electronic equipment
MEM18.58C Modify electronic equipment
MEM18.60B Maintain, repair control instrumentation – single and multiple loop control
systems
MEM18.62B Install, maintain and calibrate instrumentation sensors, transmitters and final
control elements
MEM18.63B Terminate signal and data cables
MEM18.64B Maintain instrumentation system components
MEM18.65B Diagnose and repair digital equipment and components
Specialisation units Check
MEM12.23A Perform engineering measurements
MEM12.24A Perform computations
MEM13.14A Apply principles of occupational health and safety in the work environment
MEM14.4A Plan to undertake a routine task
MEM14.5A Plan a complete activity
MEM15.2A Apply quality systems
MEM15.24A Apply quality procedures
MEM16.6A Organise and communicate information
MEM16.7A Work with others in a manufacturing, engineering or related environment
MEM16.8A Interact with computing technology
MEM17.3A Assist in the provision of on the job training
MEM9.2B Interpret technical drawing
MEM10.2B Terminate and connect electrical wiring
MEM10.3B Install and test electrical wiring and circuits up to 1000 volts a.c. and 1500 volts d.c.
MEM10.4B Enter and change programmable controller operational parameters
MEM10.11B Terminate and connect specialist cables
MEM12.2B Perform electrical/electronic measurement
MEM12.4B Perform precision electrical/electronic measurement
MEM18.1C Use hand tools
MEM18.2B Use power tools/hand held operations
MEM18.46B Fault find/repair electrical equipment/components up to 1000 volts a.c./1500 volts d.c.
MEM18.48B Fault find and repair/rectify basic electrical circuits
MEM18.49B Disconnect/reconnect fixed wired equipment up to 1000 volts a.c./1500 volts d.c.
MEM18.51B Fault find and repair/rectify complex electrical circuits

 

  
Go to Top  
Accessibility Copyright Disclaimer Privacy Webmaster
Last updated: 8 October, 2007
 NSW Department of Education and Training
Go to Top